EASA AD 2026-0216, AD 2026-0217, AD 2026-0218 and PAD 26-138
Three final EASA directives, effective 18, 26 and 27 November 2026, cover A380 wing mid-spars, ATR 42-500 and 72-212A horizontal stabilisers, and A350 ALS Part 2. PAD 26-138, on listed A330 engine mounts, is a proposal open until 11 December.
Organizational byline
Updated November 16, 2026
5 min read

News. Three of these four EASA documents are final directives. PAD 26-138 is a proposal. The photograph is Air France A380 F-HPJA on 12 November 2011. It is only an A380, not an identified serial from AD 2026-0216, and not an ATR, an A350 or an A330.
AD 2026-0216, A380 wing mid-spars, is final
EASA AD 2026-0216 was issued on 11 November 2026 and is effective 18 November 2026. It applies to Airbus A380-841, A380-842 and A380-861 aeroplanes, all manufacturer serial numbers, under type-certificate data sheet EASA.A.110. It supersedes emergency AD 2026-0119-E, dated 22 June 2026. The compliance table uses 24 June 2026 as the effective date of that emergency AD.
EASA says findings on an A380 led Airbus to identify a condition that could reduce wing structural integrity. The new AD keeps the emergency AD, adds serial numbers, and amends the inspections under Airbus Alert Operators Transmission A57R030-26, original issue 6 November 2026. EASA calls it interim.
Group 1 is serial numbers 190, 202, 203, 209 and 228: a special detailed inspection before next flight after 24 June 2026, by contacting Airbus. For that initial inspection, a ferry of up to 3 flight cycles, non-ETOPS and with no passengers, is allowed to reach a place where the work can be done. Group 2 is serial numbers 30, 42, 55, 56, 105, 142, 184, 187, 208, 227 and 234: within 25 flight cycles after 24 June 2026, again by contacting Airbus. Group 3 is serial numbers 57, 77, 103, 191, 226, 229, 240 and 241: before 31 January 2027, under the alert transmission. Group 4 is every other serial number. Storage longer than 12 months requires an inspection before return to service. Repeats are within 36 months after return to service, and not later than 42 months after the inspection started. A discrepancy means contacting Airbus before next flight. Results, including none, are due within 30 days. EASA also asks for comments until 9 December 2026. That request does not move the 18 November effective date.
AD 2026-0217, ATR horizontal stabiliser, is final
EASA AD 2026-0217 was issued on 12 November 2026 and is effective 26 November 2026. It supersedes AD 2025-0110, dated 14 May 2025. Applicability is ATR 42-500 and ATR 72-212A aeroplanes whose serial numbers are in the service bulletins named in the AD, not every ATR 42 or 72. The type-certificate data sheet is EASA.A.084.
It requires one detailed inspection of the horizontal-stabiliser leading-edge ribs, the boxes and forward back-up fitting, and of the front spar web and centre-box interior. EASA says loose fasteners and cracks were found, and that manufacturing deviations may affect a list of tailplanes. Group 1, serials in Revision 04 that are not Group 2, is due within 24 months after 6 July 2023. Groups 2 and 3 are due within 20 months after 28 May 2025. EASA says that shorter time is the change for those two groups. Group 2 serials are printed in the AD. Group 3 serials are in the second pair of bulletins. An aeroplane can be in Group 1 and Group 3, or Group 2 and Group 3. A discrepancy means contacting ATR before next flight. Comments on this final AD are open until 10 December 2026.
The bulletins are ATR42-55-0020 and ATR72-55-1013 at Revision 04, and ATR42-55-0025 and ATR72-55-1018 at Revision 01, each of those revisions dated 6 June 2025.
AD 2026-0218, A350 ALS Part 2, is final
EASA AD 2026-0218 was issued on 13 November 2026 and is effective 27 November 2026. It applies to all A350-941 and A350-1041 aeroplanes, type-certificate data sheet EASA.A.151. It supersedes AD 2025-0204, dated 19 September 2025, and AD 2026-0034, dated 23 February 2026. Those required ALS Part 2 Revision 11 and Variation 11.1. This AD requires ALS Part 2 Revision 12, dated 1 July 2026, and an approved-maintenance-programme revision within 12 months. EASA had posted it as PAD 26-122 from 9 October to 6 November 2026 and says no comments came in.
PAD 26-138, A330 engine mounts, is a proposal
PAD 26-138, issued 13 November 2026, is not an AD. Comments close 11 December 2026. The effective-date line is still to be determined. It supersedes nothing. It would apply only to Airbus A330-201, A330-202, A330-203, A330-301, A330-302 and A330-303 aeroplanes, all serial numbers, not to the rest of the A330 family.
An affected part is engine forward mount platform part number 1843M81G01, serials in Appendix 1, unless it passed a fluorescent penetrant inspection to GE instructions on 1 January 2025 or later, or was last inspected somewhere other than GE Evergreen Engine Services. EASA says that, between 2020 and 2024, that inspection may not have been done properly at that facility, which could blunt the airworthiness-limitation task and possibly lead to part failure and in-flight engine separation. The PAD does not report a separation. A Group 1 aeroplane would have to replace the engine before the part reaches 4,700 flight cycles since the last penetrant inspection. Airbus Service Bulletin A330-71-3045 is original issue 2 October 2026. GE's cited bulletin is CF6-80E1 72-0609. The serial list stays in the PAD.
Sources
- EASA AD 2026-0216 and PDF
- EASA AD 2026-0217 and PDF
- EASA AD 2026-0218 and PDF
- EASA PAD 26-138 and PDF



